1. the inspection method for the gradient of adjacent plates of special-shaped steel formwork. Generally, the mold steel 4Cr13 is customized and measured with a level and wedge-shaped feeler gauge.

2.鋼模板表面平面度檢驗

2. steel formwork surface flatness inspection

其檢驗方式是在挑選具備象征性的部位，4cr13模具鋼加工用2m直尺和楔形塞尺測量鋼模板表面平面度，取較大誤差值，讀值mm。

The inspection method is to select symbolic parts, use 2m ruler and wedge feeler gauge to measure the flatness of the steel formwork surface for 4Cr13 mold steel processing, take the larger error value, and read the value to mm.

3.鋼模板垂直角度檢驗

3. vertical angle inspection of steel formwork

模板垂直角度檢驗方式與建筑物(預制構件)垂直角度檢驗方式同樣。可以選用垂直線檢驗或用水平儀檢驗，視建筑物(預制構件)模板相對高度和規定的精度采用。

The inspection method of formwork vertical angle is the same as that of building (prefabricated component). Vertical line inspection or level inspection can be selected, depending on the relative height of the building (prefabricated component) formwork and the specified accuracy.

4.模具鋼4cr13廠家結構內尺寸檢驗

4. inspection of internal dimension of die steel 4Cr13 manufacturer

公路橋梁鋼模板生產廠家f詳細介紹結構內尺寸按照規定檢驗長、寬、高三個尺寸，以一尺立即量出結果為好，針對基本、墩、臺、墻等模內尺寸比較大部位還需查驗它的直線之差，各自查驗它的上沿和下沿尺寸之差，及其陰陽角一部分狀況。

The manufacturer F of steel formwork for highway bridges introduced in detail that the internal dimensions of the structure were inspected in terms of length, width and height according to the regulations. It is better to measure the results immediately with one foot. For the parts with relatively large internal dimensions such as the basic, pier, abutment and wall, it is also necessary to check the difference of their straight lines, and check the difference of their upper and lower edges, as well as part of their internal and external corners.

5.偏移檢驗。灌溉砼時，先向灌溉四個戰爭固定不動模板，隨后四周按序勻稱提高，應該有專職人員用心翻車機，防止蜂窩狀、表面和洞。

5. deviation inspection. When irrigating concrete, the four fixed formworks shall be irrigated first, and then the four sides shall be raised in order. Full time personnel shall carefully use the car dumper to prevent honeycomb, surface and dog hole.

懸吊訓練鍍鋅鋼絲繩靠殘害模板五米處，運用橡膠軟管捆扎好，防止炮崩壞三。每片挪動前開展查驗，一旦毀壞超限額按照規定好。具備充分的抗壓強度、彎曲剛度和可靠性，能靠譜地承擔模板施工工藝要求的各類工程施工載荷，并確保形變不超過容許范疇。

The galvanized steel wire rope for suspension training shall be tied with rubber hose at the place five meters away from the damaged formwork to prevent blasting damage. Each piece shall be inspected before moving. Once it is damaged beyond the limit, it shall be solved according to the regulations. It has sufficient compressive strength, bending stiffness and reliability, can reliably bear various engineering construction loads required by the formwork construction process, and ensure that the deformation does not exceed the allowable range.

以上就是為大家介紹的有關山東模具鋼http://www.6886774.cn的詳細的介紹,希望對您有所幫助.如果您有什么疑問的話,歡迎聯系我們.我們將以的態度,為您提供服務.

The above is about Shandong die steel http://www.6886774.cn I hope it will be helpful to you If you have any questions, please contact us We will provide you with professional service